605 lines
13 KiB
C
605 lines
13 KiB
C
#include "sys.h"
|
||
#include "Lcd_Driver.h"
|
||
#include "delay.h"
|
||
#include "SPI.h"
|
||
//********************************************************************************
|
||
|
||
//DevEBox 大越电子（嵌入式开发网）
|
||
//淘宝店铺：mcudev.taobao.com
|
||
//淘宝店铺：shop389957290.taobao.com
|
||
|
||
//********************************************************************************
|
||
|
||
|
||
//STM32核心板例程
|
||
//库函数版本例程
|
||
|
||
//本测试程序使用的是模拟SPI接口驱动
|
||
//可自由更改接口IO配置，使用任意最少4 IO即可完成本款液晶驱动显示
|
||
|
||
/******************************************************************************
|
||
接口定义在Lcd_Driver.h内定义，请根据接线修改并修改相应IO初始化LCD_GPIO_Init()
|
||
|
||
// ----------------------------------------------------------------
|
||
// VCC 接5V或3.3v电源
|
||
// GND 电源地
|
||
// D1 接PB15（SDI）
|
||
// D0 接PB13（SCL）
|
||
// CS 接PB12 片选
|
||
// RST 接PB14 系统复位
|
||
// DC 接PB1 命令/数据
|
||
// BLK 接PB0 背光控制
|
||
// ----------------------------------------------------------------
|
||
|
||
// #define LCD_SDI //PB15
|
||
// #define LCD_SCL //PB13
|
||
// #define LCD_CS //PB12
|
||
// #define LCD_SDO //PB14
|
||
// #define LCD_RS //PB1
|
||
// #define LCD_BLK //PB0
|
||
*******************************************************************************/
|
||
|
||
/**************************************************************************************
|
||
|
||
函数名称: void LCD_GPIO_Init(void)
|
||
|
||
功能描述: 液晶IO初始化配置
|
||
输 入:
|
||
输 出:
|
||
|
||
//DevEBox 大越电子（嵌入式开发网）
|
||
//淘宝店铺：mcudev.taobao.com
|
||
//淘宝店铺：shop389957290.taobao.com
|
||
|
||
**************************************************************************************/
|
||
|
||
//液晶IO初始化配置
|
||
void LCD_GPIO_Init(void)
|
||
{
|
||
|
||
GPIO_InitTypeDef GPIO_Initure;
|
||
__HAL_RCC_GPIOB_CLK_ENABLE(); //开启PB时钟
|
||
|
||
|
||
GPIO_Initure.Pin=GPIO_PIN_0 |GPIO_PIN_1 | GPIO_PIN_12; //PB
|
||
GPIO_Initure.Mode=GPIO_MODE_OUTPUT_PP; //推挽输出
|
||
GPIO_Initure.Pull=GPIO_PULLUP; //上拉
|
||
GPIO_Initure.Speed=GPIO_SPEED_FREQ_VERY_HIGH; //高速
|
||
HAL_GPIO_Init(GPIOB,&GPIO_Initure); //初始化
|
||
|
||
HAL_GPIO_WritePin(GPIOB,GPIO_PIN_0,GPIO_PIN_SET); //PB0置1
|
||
HAL_GPIO_WritePin(GPIOB,GPIO_PIN_1,GPIO_PIN_SET); //PB1置1
|
||
HAL_GPIO_WritePin(GPIOB,GPIO_PIN_12,GPIO_PIN_SET); //PB12置1
|
||
|
||
|
||
|
||
SPI2_Init(); //初始化硬件SPI2
|
||
|
||
SPI2_SetSpeed(SPI_BAUDRATEPRESCALER_8); //设置高速模式
|
||
|
||
// LCD_BLK_SET;//开启背光
|
||
// LCD_BLK_CLR;//关闭背光
|
||
LCD_BLK_SET;//开启背光
|
||
|
||
}
|
||
|
||
|
||
/****************************************************************************
|
||
* 名 称：void SPIv_WriteData(u8 Data)
|
||
* 功 能：STM32_SPI写一个字节数据底层函数
|
||
* 入口参数：Data
|
||
* 出口参数：无
|
||
* 说 明：STM32_SPI读写一个字节数据底层函数
|
||
|
||
|
||
//STM32H7工程模板-HAL库函数版本
|
||
//DevEBox 大越创新
|
||
//嵌入式开发网
|
||
//淘宝店铺：mcudev.taobao.com
|
||
//淘宝店铺：shop389957290.taobao.com
|
||
|
||
****************************************************************************/
|
||
void SPI_WriteData(u8 Data)
|
||
{
|
||
//// unsigned char i=0;
|
||
//// for(i=8;i>0;i--)
|
||
//// {
|
||
//// if(Data&0x80)
|
||
//// LCD_SDA_SET; //输出数据
|
||
//// else LCD_SDA_CLR;
|
||
////
|
||
//// LCD_SCL_CLR;
|
||
//// LCD_SCL_SET;
|
||
//// Data<<=1;
|
||
//// }
|
||
|
||
SPI2_ReadWriteByte(Data); //使用单片机硬件SPI接口驱动--硬件接口，可以提高写屏速度
|
||
}
|
||
|
||
|
||
/****************************************************************************
|
||
* 名 称：void Lcd_WriteIndex(u8 idx)
|
||
* 功 能：写 ST7735S 控制器寄存器地址
|
||
* 入口参数：idx 寄存器地址
|
||
* 出口参数：无
|
||
* 说 明：调用前需先选中控制器，内部函数
|
||
* 调用方法：Lcd_WriteIndex(0x00);
|
||
|
||
//STM32H7工程模板-HAL库函数版本
|
||
//DevEBox 大越创新
|
||
//嵌入式开发网
|
||
//淘宝店铺：mcudev.taobao.com
|
||
//淘宝店铺：shop389957290.taobao.com
|
||
|
||
****************************************************************************/
|
||
void Lcd_WriteIndex(u8 Index)
|
||
{
|
||
|
||
//SPI 写命令时序开始
|
||
LCD_CS_CLR;
|
||
LCD_RS_CLR; //写入命令
|
||
SPI_WriteData(Index);
|
||
LCD_CS_SET;
|
||
}
|
||
|
||
/****************************************************************************
|
||
* 名 称：void Lcd_WriteData(u8 dat)
|
||
* 功 能：写 ST7735S 寄存器数据
|
||
* 入口参数：dat 寄存器数据
|
||
* 出口参数：无
|
||
* 说 明：向控制器指定地址写入数据，调用前需先写寄存器地址，内部函数
|
||
* 调用方法：Lcd_WriteData(0x30)
|
||
|
||
//STM32H7工程模板-HAL库函数版本
|
||
//DevEBox 大越创新
|
||
//嵌入式开发网
|
||
//淘宝店铺：mcudev.taobao.com
|
||
//淘宝店铺：shop389957290.taobao.com
|
||
|
||
****************************************************************************/
|
||
void Lcd_WriteData(u8 Data)
|
||
{
|
||
|
||
LCD_CS_CLR;
|
||
LCD_RS_SET; //写入数据
|
||
SPI_WriteData(Data);
|
||
LCD_CS_SET;
|
||
}
|
||
|
||
|
||
/****************************************************************************
|
||
* 名 称：void Lcd_WriteReg(u8 Index,u8 Data)
|
||
* 功 能：
|
||
|
||
//写寄存器函数
|
||
|
||
//STM32H7工程模板-HAL库函数版本
|
||
//DevEBox 大越创新
|
||
//嵌入式开发网
|
||
//淘宝店铺：mcudev.taobao.com
|
||
//淘宝店铺：shop389957290.taobao.com
|
||
|
||
****************************************************************************/
|
||
|
||
void Lcd_WriteReg(u8 Index,u8 Data)
|
||
{
|
||
Lcd_WriteIndex(Index);
|
||
Lcd_WriteData(Data);
|
||
}
|
||
|
||
/****************************************************************************
|
||
* 名 称：void LCD_WriteData_16Bit(uint16_t Data)
|
||
* 功 能：
|
||
|
||
//向液晶屏写一个16位数据
|
||
|
||
//STM32H7工程模板-HAL库函数版本
|
||
//DevEBox 大越创新
|
||
//嵌入式开发网
|
||
//淘宝店铺：mcudev.taobao.com
|
||
//淘宝店铺：shop389957290.taobao.com
|
||
|
||
****************************************************************************/
|
||
|
||
|
||
void LCD_WriteData_16Bit(uint16_t Data)
|
||
{
|
||
LCD_CS_CLR;
|
||
LCD_RS_SET;
|
||
SPI_WriteData(Data>>8); //写入高8位数据
|
||
SPI_WriteData(Data); //写入低8位数据
|
||
LCD_CS_SET;
|
||
}
|
||
|
||
|
||
|
||
/****************************************************************************
|
||
* 名 称：void Lcd_Reset(void)
|
||
* 功 能：
|
||
|
||
//液晶屏复位函数
|
||
|
||
//STM32H7工程模板-HAL库函数版本
|
||
//DevEBox 大越创新
|
||
//嵌入式开发网
|
||
//淘宝店铺：mcudev.taobao.com
|
||
//淘宝店铺：shop389957290.taobao.com
|
||
|
||
****************************************************************************/
|
||
|
||
|
||
|
||
void Lcd_Reset(void)
|
||
{
|
||
LCD_RST_Clr;
|
||
delay_ms(100);
|
||
LCD_RST_Set;
|
||
delay_ms(100);
|
||
}
|
||
|
||
|
||
//管理LCD重要参数
|
||
//默认为竖屏
|
||
_lcd_dev lcddev;
|
||
|
||
|
||
|
||
/****************************************************************************
|
||
* 名 称：void LCD_SetParam(void)
|
||
* 功 能：
|
||
|
||
//设置LCD参数
|
||
//方便进行横竖屏模式切换
|
||
|
||
//STM32H7工程模板-HAL库函数版本
|
||
//DevEBox 大越创新
|
||
//嵌入式开发网
|
||
//淘宝店铺：mcudev.taobao.com
|
||
//淘宝店铺：shop389957290.taobao.com
|
||
|
||
****************************************************************************/
|
||
|
||
|
||
void LCD_SetParam(void)
|
||
{
|
||
lcddev.wramcmd=0x2C;
|
||
#if USE_HORIZONTAL==1 //使用横屏
|
||
lcddev.dir=1;//横屏
|
||
lcddev.width=160;
|
||
lcddev.height=128;
|
||
lcddev.setxcmd=0x2A;
|
||
lcddev.setycmd=0x2B;
|
||
Lcd_WriteReg(0x36,0xA0);
|
||
|
||
#else//竖屏
|
||
lcddev.dir=0;//竖屏
|
||
lcddev.width=128;
|
||
lcddev.height=160;
|
||
lcddev.setxcmd=0x2A;
|
||
lcddev.setycmd=0x2B;
|
||
Lcd_WriteReg(0x36,0xC0);
|
||
#endif
|
||
}
|
||
|
||
|
||
/*************************************************
|
||
函数名：LCD_Set_Region
|
||
功能：设置lcd显示区域，在此区域写点数据自动换行
|
||
入口参数：xy起点和终点,Y_IncMode表示先自增y再自增x
|
||
返回值：无
|
||
|
||
//STM32H7工程模板-HAL库函数版本
|
||
//DevEBox 大越创新
|
||
//嵌入式开发网
|
||
//淘宝店铺：mcudev.taobao.com
|
||
//淘宝店铺：shop389957290.taobao.com
|
||
|
||
*************************************************/
|
||
void Lcd_SetRegion(u16 x_start,u16 y_start,u16 x_end,u16 y_end)
|
||
{
|
||
#if USE_HORIZONTAL==1 //使用横屏
|
||
|
||
Lcd_WriteIndex(0x2a);
|
||
Lcd_WriteData(0x00);
|
||
Lcd_WriteData(x_start);
|
||
Lcd_WriteData(0x00);
|
||
Lcd_WriteData(x_end);
|
||
|
||
Lcd_WriteIndex(0x2b);
|
||
Lcd_WriteData(0x00);
|
||
Lcd_WriteData(y_start);
|
||
Lcd_WriteData(0x00);
|
||
Lcd_WriteData(y_end);
|
||
|
||
|
||
#else
|
||
Lcd_WriteIndex(0x2a);
|
||
Lcd_WriteData(0x00);
|
||
Lcd_WriteData(x_start);
|
||
Lcd_WriteData(0x00);
|
||
Lcd_WriteData(x_end);
|
||
|
||
Lcd_WriteIndex(0x2b);
|
||
Lcd_WriteData(0x00);
|
||
Lcd_WriteData(y_start);
|
||
Lcd_WriteData(0x00);
|
||
Lcd_WriteData(y_end);
|
||
#endif
|
||
|
||
Lcd_WriteIndex(0x2c); //开始写入GRAM
|
||
|
||
}
|
||
|
||
/*************************************************
|
||
函数名：LCD_Set_XY
|
||
功能：设置lcd显示起始点
|
||
入口参数：xy坐标
|
||
返回值：无
|
||
|
||
//STM32H7工程模板-HAL库函数版本
|
||
//DevEBox 大越创新
|
||
//嵌入式开发网
|
||
//淘宝店铺：mcudev.taobao.com
|
||
//淘宝店铺：shop389957290.taobao.com
|
||
|
||
*************************************************/
|
||
void Lcd_SetXY(u16 x,u16 y)
|
||
{
|
||
//Lcd_SetRegion(x,y,x,y);
|
||
#if USE_HORIZONTAL==1 //使用横屏
|
||
|
||
Lcd_SetRegion(x+1,y+2,x+1,y+2);
|
||
#else
|
||
Lcd_SetRegion(x+2,y+1,x+2,y+1);
|
||
#endif
|
||
}
|
||
|
||
|
||
/*************************************************
|
||
函数名：LCD_DrawPoint
|
||
功能：画一个点
|
||
入口参数：无
|
||
返回值：无
|
||
|
||
//STM32H7工程模板-HAL库函数版本
|
||
//DevEBox 大越创新
|
||
//嵌入式开发网
|
||
//淘宝店铺：mcudev.taobao.com
|
||
//淘宝店铺：shop389957290.taobao.com
|
||
|
||
*************************************************/
|
||
void Gui_DrawPoint(u16 x,u16 y,u16 Data)
|
||
{
|
||
//Lcd_SetRegion(x,y,x+1,y+1);
|
||
#if USE_HORIZONTAL==1 //使用横屏
|
||
|
||
Lcd_SetRegion(x+1,y+2,x+2,y+3);
|
||
|
||
#else
|
||
|
||
Lcd_SetRegion(x+2,y+1,x+3,y+2);
|
||
|
||
#endif
|
||
Lcd_WriteData(Data>>8);
|
||
Lcd_WriteData(Data);
|
||
|
||
}
|
||
|
||
/*****************************************
|
||
函数功能：读TFT某一点的颜色
|
||
出口参数：color 点颜色值
|
||
******************************************/
|
||
//unsigned int Lcd_ReadPoint(u16 x,u16 y)
|
||
//{
|
||
// unsigned int Data;
|
||
// Lcd_SetXY(x,y);
|
||
// Lcd_WriteData(Data);
|
||
// return Data;
|
||
//}
|
||
|
||
|
||
|
||
/*************************************************
|
||
函数名：Lcd_Clear
|
||
功能：全屏清屏函数
|
||
入口参数：填充颜色COLOR
|
||
返回值：无
|
||
|
||
//STM32H7工程模板-HAL库函数版本
|
||
//DevEBox 大越创新
|
||
//嵌入式开发网
|
||
//淘宝店铺：mcudev.taobao.com
|
||
//淘宝店铺：shop389957290.taobao.com
|
||
|
||
*************************************************/
|
||
void Lcd_Clear(u16 Color)
|
||
{
|
||
unsigned int i,m;
|
||
|
||
#if USE_HORIZONTAL==1 //使用横屏
|
||
|
||
//Lcd_SetRegion(2,1,X_MAX_PIXEL+1,Y_MAX_PIXEL);
|
||
Lcd_SetRegion(1,2,X_MAX_PIXEL,Y_MAX_PIXEL+1);
|
||
|
||
Lcd_WriteIndex(0x2C);
|
||
|
||
for(i=0;i<Y_MAX_PIXEL;i++)
|
||
for(m=0;m<X_MAX_PIXEL;m++)
|
||
{
|
||
Lcd_WriteData(Color>>8);
|
||
Lcd_WriteData(Color);
|
||
}
|
||
|
||
|
||
#else
|
||
Lcd_SetRegion(2,1,X_MAX_PIXEL+1,Y_MAX_PIXEL);
|
||
|
||
Lcd_WriteIndex(0x2C);
|
||
|
||
for(i=0;i<Y_MAX_PIXEL;i++)
|
||
for(m=0;m<X_MAX_PIXEL;m++)
|
||
{
|
||
Lcd_WriteData(Color>>8);
|
||
Lcd_WriteData(Color);
|
||
}
|
||
|
||
#endif
|
||
|
||
}
|
||
|
||
|
||
|
||
/*************************************************
|
||
函数名：void Lcd_Init(void)
|
||
功能：液晶屏初始化函数
|
||
|
||
//STM32H7工程模板-HAL库函数版本
|
||
//DevEBox 大越创新
|
||
//嵌入式开发网
|
||
//淘宝店铺：mcudev.taobao.com
|
||
//淘宝店铺：shop389957290.taobao.com
|
||
|
||
*************************************************/
|
||
|
||
void Lcd_Init(void)
|
||
{
|
||
|
||
|
||
LCD_GPIO_Init();//使用模拟SPI 初始化IO接口
|
||
|
||
Lcd_Reset(); //复位液晶屏
|
||
|
||
|
||
Lcd_WriteIndex(0x11);//Sleep exit
|
||
|
||
delay_ms (200);
|
||
|
||
Lcd_WriteIndex(0xB1);
|
||
Lcd_WriteData(0x05);
|
||
Lcd_WriteData(0x3C);
|
||
Lcd_WriteData(0x3C);
|
||
Lcd_WriteIndex(0xB2);
|
||
Lcd_WriteData(0x05);
|
||
Lcd_WriteData(0x3C);
|
||
Lcd_WriteData(0x3C);
|
||
Lcd_WriteIndex(0xB3);
|
||
Lcd_WriteData(0x05);
|
||
Lcd_WriteData(0x3C);
|
||
Lcd_WriteData(0x3C);
|
||
Lcd_WriteData(0x05);
|
||
Lcd_WriteData(0x3C);
|
||
Lcd_WriteData(0x3C);
|
||
//------------------------------------End ST7735S Frame Rate---------------------------------//
|
||
Lcd_WriteIndex(0xB4); //Dot inversion
|
||
Lcd_WriteData(0x03);
|
||
//------------------------------------ST7735S Power Sequence---------------------------------//
|
||
Lcd_WriteIndex(0xC0);
|
||
Lcd_WriteData(0x28);
|
||
Lcd_WriteData(0x08);
|
||
Lcd_WriteData(0x04);
|
||
Lcd_WriteIndex(0xC1);
|
||
Lcd_WriteData(0XC0);
|
||
Lcd_WriteIndex(0xC2);
|
||
Lcd_WriteData(0x0D);
|
||
Lcd_WriteData(0x00);
|
||
Lcd_WriteIndex(0xC3);
|
||
Lcd_WriteData(0x8D);
|
||
Lcd_WriteData(0x2A);
|
||
Lcd_WriteIndex(0xC4);
|
||
Lcd_WriteData(0x8D);
|
||
Lcd_WriteData(0xEE);
|
||
//---------------------------------End ST7735S Power Sequence-------------------------------------//
|
||
Lcd_WriteIndex(0xC5); //VCOM
|
||
Lcd_WriteData(0x1A);
|
||
Lcd_WriteIndex(0x36); //MX, MY, RGB mode
|
||
Lcd_WriteData(0xC0);
|
||
//------------------------------------ST7735S Gamma Sequence---------------------------------//
|
||
Lcd_WriteIndex(0xE0);
|
||
Lcd_WriteData(0x04);
|
||
Lcd_WriteData(0x22);
|
||
Lcd_WriteData(0x07);
|
||
Lcd_WriteData(0x0A);
|
||
Lcd_WriteData(0x2E);
|
||
Lcd_WriteData(0x30);
|
||
Lcd_WriteData(0x25);
|
||
Lcd_WriteData(0x2A);
|
||
Lcd_WriteData(0x28);
|
||
Lcd_WriteData(0x26);
|
||
Lcd_WriteData(0x2E);
|
||
Lcd_WriteData(0x3A);
|
||
Lcd_WriteData(0x00);
|
||
Lcd_WriteData(0x01);
|
||
Lcd_WriteData(0x03);
|
||
Lcd_WriteData(0x13);
|
||
Lcd_WriteIndex(0xE1);
|
||
Lcd_WriteData(0x04);
|
||
Lcd_WriteData(0x16);
|
||
Lcd_WriteData(0x06);
|
||
Lcd_WriteData(0x0D);
|
||
Lcd_WriteData(0x2D);
|
||
Lcd_WriteData(0x26);
|
||
Lcd_WriteData(0x23);
|
||
Lcd_WriteData(0x27);
|
||
Lcd_WriteData(0x27);
|
||
Lcd_WriteData(0x25);
|
||
Lcd_WriteData(0x2D);
|
||
Lcd_WriteData(0x3B);
|
||
Lcd_WriteData(0x00);
|
||
Lcd_WriteData(0x01);
|
||
Lcd_WriteData(0x04);
|
||
Lcd_WriteData(0x13);
|
||
//------------------------------------End ST7735S Gamma Sequence-----------------------------//
|
||
Lcd_WriteIndex(0x3A); //65k mode
|
||
Lcd_WriteData(0x05);
|
||
Lcd_WriteIndex(0x29); //Display on
|
||
|
||
LCD_SetParam();//设置LCD参数
|
||
|
||
}
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
/**************************************************************************************/
|
||
|
||
//STM32H7工程模板-HAL库函数版本
|
||
//DevEBox 大越创新
|
||
//嵌入式开发网
|
||
//淘宝店铺：mcudev.taobao.com
|
||
//淘宝店铺：shop389957290.taobao.com
|
||
|
||
/**************************************************************************************/
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|