首个能完整正确运行的版本
This commit is contained in:
parent
8c4c7b54b8
commit
562d317b13
@ -15,6 +15,7 @@ Servo servo; //舵机实例
|
||||
#define RELEASE_POINT 2 //释放点（使用机械臂）
|
||||
#define CARRY_POINT 3 //携带点（从底盘）
|
||||
#define GETOUT_POINT 4 //释放点（从底盘）
|
||||
#define GAIN_POINT 5 //增益点
|
||||
|
||||
//坐标点数组定义
|
||||
#define X 0
|
||||
@ -25,63 +26,61 @@ int8_t route[][3] =
|
||||
{
|
||||
{0, 0, NORMAL_POINT},
|
||||
{0, 1, NORMAL_POINT},
|
||||
{1, 1, CARRY_POINT},
|
||||
{2, 1, NORMAL_POINT},
|
||||
{2, 2, CATCH_POINT},
|
||||
{2, 3, NORMAL_POINT},
|
||||
{3, 3, GETOUT_POINT},
|
||||
{2, 3, NORMAL_POINT},
|
||||
{2, 4, NORMAL_POINT},
|
||||
{3, 4, RELEASE_POINT},
|
||||
{2, 4, NORMAL_POINT},
|
||||
{2, 3, NORMAL_POINT},
|
||||
{1, 3, NORMAL_POINT},
|
||||
{0, 3, NORMAL_POINT},
|
||||
{0, 2, CATCH_POINT},
|
||||
{1, 2, NORMAL_POINT},
|
||||
{2, 2, NORMAL_POINT},
|
||||
{3, 2, RELEASE_POINT},
|
||||
{2, 2, NORMAL_POINT},
|
||||
{2, 3, NORMAL_POINT},
|
||||
{3, 3, GETOUT_POINT},
|
||||
{2, 3, NORMAL_POINT}
|
||||
{0, 2, NORMAL_POINT},
|
||||
{-1, 2, NORMAL_POINT},
|
||||
{-1, 1, CATCH_POINT},
|
||||
{0, 1, NORMAL_POINT},
|
||||
{0, 0, NORMAL_POINT},
|
||||
{-1, 0, RELEASE_POINT}
|
||||
};
|
||||
//***************************************************************************************
|
||||
|
||||
|
||||
//****************************************可调参数****************************************
|
||||
//是否关闭爪子状态检测功能
|
||||
#define DISABLE_CLAW_CHECK
|
||||
|
||||
//抓取点移动用时
|
||||
#define CATCH_MOVE_DELAY_TIME 700
|
||||
//释放点移动用时
|
||||
#define RELEASE_MOVE_DELAY_TIME 700
|
||||
#define CATCH_MOVE_DELAY_TIME 500
|
||||
//释放点向前移动用时
|
||||
#define RELEASE_MOVE_FORWARD_DELAY_TIME 1000
|
||||
//释放点暂停用时
|
||||
#define RELEASE_STOP_DELAY_TIME 500
|
||||
//释放点向后向前移动用时
|
||||
#define RELEASE_MOVE_BACKWARD_AND_FORWARD_DELAY_TIME 460
|
||||
//增益点向后向前移动用时
|
||||
#define GAIN_MOVE_BACKWARD_AND_FORWARD_DELAY_TIME 460
|
||||
//增益点稍稍向前移动用时
|
||||
#define GAIN_MOVE_LITTLEFORWARD_DELAY_TIME 200
|
||||
|
||||
//重置留时
|
||||
#define RESET_DELAY_TIME 5000
|
||||
#define RESET_DELAY_TIME 1600
|
||||
//放下爪子用时
|
||||
#define DOWN_DELAY_TIME 1600
|
||||
//抓取留时
|
||||
#define CATCH_DELAY_TIME 5000
|
||||
#define CATCH_DELAY_TIME 2100
|
||||
//释放留时
|
||||
#define RELEASE_DELAY_TIME 5000
|
||||
#define RELEASE_DELAY_TIME 3100
|
||||
//增益放下爪子用时
|
||||
#define GAINDOWN_DELAY_TIME 1600
|
||||
//增益抓取用时
|
||||
#define GAINCATCH_DELAY_TIME 3100
|
||||
|
||||
//最大抓取尝试次数
|
||||
#define MAX_CATCH_TIMES 2
|
||||
|
||||
//（前进转）从触碰白线到开始转向延时
|
||||
#define BEFORE_FORTURN_DELAY 700
|
||||
#define BEFORE_FORTURN_DELAY 670
|
||||
//（后退转）从触碰白线到开始转向延时
|
||||
#define BEFORE_BACKTURN_DELAY 700
|
||||
#define BEFORE_BACKTURN_DELAY 500
|
||||
|
||||
//开始转到开始检测是否摆正的延时
|
||||
#define BEFORE_CHECK_STRAIGHT_DELAY 700
|
||||
|
||||
//修正循迹时单侧减速比率
|
||||
#define LINE_FIX_SPEED_RATE 0.4
|
||||
//低速重新寻线时减速比率
|
||||
#define LINE_FIND_SPEED_RATE 0.3
|
||||
//***************************************************************************************
|
||||
|
||||
|
||||
//****************************************全局变量****************************************
|
||||
// GND Pins
|
||||
//GND Pins
|
||||
uint8_t gnd_pins[4] = {14, 15, 16, 17};
|
||||
|
||||
//数组位置标记
|
||||
@ -123,6 +122,9 @@ void UpdateFlag(uint8_t jump_choice = NO_JUMP);
|
||||
//计算方向，同时更改完成转向后相对下一点的朝向
|
||||
uint8_t CalcDirection(void);
|
||||
|
||||
//由灰度比计算修正减速比
|
||||
float CalcFixSpeedRate(float gray_deviation_rate);
|
||||
|
||||
#define FRONT_END 0
|
||||
#define BACK_END 1
|
||||
#define CATCH_END 2
|
||||
@ -136,8 +138,10 @@ void LineBackward(uint8_t end_position, float speed_rate = 1.0);
|
||||
//直行或后退或转向，完成后离开函数但不停止。会自动跳过无需前往的释放点
|
||||
void TurnDirection(float speed_rate = 1.0);
|
||||
|
||||
#define CATCH_TYPE_CATCH 0
|
||||
#define CATCH_TYPE_GAIN 1
|
||||
//抓取环，并判定是否抓取成功
|
||||
bool CatchAndCheck(float speed = 1.0);
|
||||
bool CatchAndCheck(uint8_t type = CATCH_TYPE_CATCH, float speed = 1.0);
|
||||
|
||||
//打开爪子，并判断爪子是否能正常工作
|
||||
bool OpenClawAndCheck(void);
|
||||
@ -159,7 +163,19 @@ int loop_time = 0;
|
||||
//中断函数，用于调试时暂停程序
|
||||
void DebugPause(void)
|
||||
{
|
||||
//记录之前的运动状态
|
||||
uint8_t current_direction = move.GetCurrentMove(); //当前运动状态
|
||||
float current_speed_rate = move.GetCurrentSpeedRate(); //当前运动速度比率
|
||||
float current_turn_speed_rate = move.GetCurrentTurnSpeedRate(); //当前转向时一侧减速的比率
|
||||
|
||||
//停止运动
|
||||
move.Stop();
|
||||
|
||||
//等待低电平结束
|
||||
while (digitalRead(DEBUG_PAUSE_PIN) == LOW) {}
|
||||
|
||||
//恢复之前的运动
|
||||
move.MoveDirection(current_direction, current_speed_rate, current_turn_speed_rate);
|
||||
}
|
||||
|
||||
//错误消息函数，用于在出现致命错误后结束程序
|
||||
@ -266,6 +282,11 @@ void loop()
|
||||
|
||||
if (!is_claw_catch && is_claw_ok) //爪子上无环且状态正常
|
||||
{
|
||||
move.Stop(); //停止前进
|
||||
|
||||
servo.Down(); //放下爪子
|
||||
delay(DOWN_DELAY_TIME);
|
||||
|
||||
//沿线直行，在抓取位置离开函数
|
||||
LineForward(CATCH_END);
|
||||
|
||||
@ -274,7 +295,7 @@ void loop()
|
||||
|
||||
//抓取
|
||||
if (!CatchAndCheck())
|
||||
is_carry = true; //抓取失败
|
||||
is_carry = true; //抓取失败，视为底盘携带
|
||||
}
|
||||
else //未进行抓取
|
||||
{
|
||||
@ -293,32 +314,51 @@ void loop()
|
||||
//情况三：刚完整经过普通点，下一个点为释放点（使用机械臂）
|
||||
else if (passed_flag_type == NORMAL_POINT && next_flag_type == RELEASE_POINT)
|
||||
{
|
||||
//沿线直行，在释放位置离开函数
|
||||
//沿线直行，在释放柱离开函数
|
||||
LineForward(RELEASE_END);
|
||||
|
||||
//停止前进
|
||||
move.Stop();
|
||||
delay(RELEASE_STOP_DELAY_TIME);
|
||||
|
||||
//无循迹后退到真实释放位置
|
||||
move.Backward();
|
||||
delay(RELEASE_MOVE_BACKWARD_AND_FORWARD_DELAY_TIME);
|
||||
|
||||
//停止后退
|
||||
move.Stop();
|
||||
|
||||
//释放
|
||||
servo.Release();
|
||||
delay(RELEASE_DELAY_TIME); //释放留时
|
||||
is_claw_catch = false;
|
||||
|
||||
//下一点朝向为后
|
||||
next_position = BACK_NEXT;
|
||||
}
|
||||
//情况四：刚完整经过释放点（使用机械臂），下一个点为普通点
|
||||
else if (passed_flag_type == RELEASE_POINT && next_flag_type == NORMAL_POINT)
|
||||
{
|
||||
//沿线后退，到后端传感器接触下一条线离开函数
|
||||
LineBackward(BACK_END);
|
||||
|
||||
//停止后退
|
||||
move.Stop();
|
||||
|
||||
//机械臂复原
|
||||
servo.Reset();
|
||||
delay(RESET_DELAY_TIME); //复原留时
|
||||
delay(RESET_DELAY_TIME);
|
||||
|
||||
//无循迹前进到释放柱
|
||||
move.Forward();
|
||||
delay(RELEASE_MOVE_BACKWARD_AND_FORWARD_DELAY_TIME);
|
||||
|
||||
//下一点朝向为后
|
||||
next_position = BACK_NEXT;
|
||||
|
||||
//停止前进
|
||||
move.Stop();
|
||||
delay(RELEASE_STOP_DELAY_TIME);
|
||||
|
||||
//!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
|
||||
//route[4][2] = CATCH_POINT;
|
||||
}
|
||||
//情况四：刚完整经过释放点（使用机械臂）或增益抓取点，下一个点为普通点
|
||||
else if ((passed_flag_type == RELEASE_POINT || passed_flag_type == GAIN_POINT) && next_flag_type == NORMAL_POINT)
|
||||
{
|
||||
//底盘携带清空
|
||||
is_carry = false;
|
||||
|
||||
//沿线后退，到后端传感器接触下一条线离开函数
|
||||
LineBackward(BACK_END);
|
||||
|
||||
//继续后退或转向
|
||||
TurnDirection();
|
||||
@ -341,6 +381,7 @@ void loop()
|
||||
//沿线后退，到前端传感器接触线离开函数
|
||||
LineBackward(FRONT_END);
|
||||
|
||||
//底盘携带清空
|
||||
is_carry = false;
|
||||
|
||||
//沿线后退，到后端传感器接触线离开函数
|
||||
@ -349,6 +390,57 @@ void loop()
|
||||
//继续后退或转向
|
||||
TurnDirection();
|
||||
}
|
||||
//情况七：刚完整经过普通点，下一个点为增益抓取点
|
||||
else if (passed_flag_type == NORMAL_POINT && next_flag_type == GAIN_POINT)
|
||||
{
|
||||
if (!is_claw_ok) //爪子状态不正常
|
||||
{
|
||||
move.Stop(); //停止前进
|
||||
OpenClawAndCheck(); //再次检测爪子是否正常
|
||||
}
|
||||
|
||||
if (is_claw_ok) //爪子状态正常
|
||||
{
|
||||
//沿线直行，在释放柱（增益柱）离开函数
|
||||
LineForward(RELEASE_END);
|
||||
|
||||
//停止前进
|
||||
move.Stop();
|
||||
delay(RELEASE_STOP_DELAY_TIME);
|
||||
|
||||
//无循迹后退到真实抓取位置
|
||||
move.Backward();
|
||||
delay(GAIN_MOVE_BACKWARD_AND_FORWARD_DELAY_TIME);
|
||||
|
||||
//停止后退
|
||||
move.Stop();
|
||||
|
||||
//放下爪子
|
||||
servo.GainDown();
|
||||
delay(GAINDOWN_DELAY_TIME);
|
||||
|
||||
//稍稍无循迹前进
|
||||
move.Forward();
|
||||
delay(GAIN_MOVE_LITTLEFORWARD_DELAY_TIME);
|
||||
|
||||
//停止前进
|
||||
move.Stop();
|
||||
|
||||
//抓取
|
||||
CatchAndCheck(CATCH_TYPE_GAIN);
|
||||
|
||||
//无循迹前进到释放柱（增益柱）
|
||||
move.Forward();
|
||||
delay(GAIN_MOVE_BACKWARD_AND_FORWARD_DELAY_TIME);
|
||||
}
|
||||
|
||||
//下一点朝向为后
|
||||
next_position = BACK_NEXT;
|
||||
|
||||
//停止前进
|
||||
move.Stop();
|
||||
delay(RELEASE_STOP_DELAY_TIME);
|
||||
}
|
||||
//出现错误
|
||||
else
|
||||
{
|
||||
@ -526,6 +618,13 @@ uint8_t CalcDirection(void)
|
||||
}
|
||||
|
||||
|
||||
//由灰度比计算修正减速比
|
||||
float CalcFixSpeedRate(float gray_deviation_rate)
|
||||
{
|
||||
return -50.0 * pow((gray_deviation_rate - 1.0), 2.0) + 1.0;
|
||||
}
|
||||
|
||||
|
||||
//沿线直行，在触发条件后离开函数但不停止
|
||||
void LineForward(uint8_t end_position, float speed_rate)
|
||||
{
|
||||
@ -538,16 +637,18 @@ void LineForward(uint8_t end_position, float speed_rate)
|
||||
|
||||
//记录开始时间
|
||||
unsigned long begin_time = millis();
|
||||
//记录灰度传感器匹配次数
|
||||
uint8_t gray_match_time = 0;
|
||||
|
||||
while(1)
|
||||
{
|
||||
if (!sensor.IsWhite(GRAY_3) && sensor.IsWhite(GRAY_4)) //左侧越线
|
||||
{
|
||||
move.ForRightward(speed_rate, LINE_FIX_SPEED_RATE);
|
||||
move.ForRightward(speed_rate, CalcFixSpeedRate(sensor.GrayDeviationRate(GRAY_3)));
|
||||
}
|
||||
else if (sensor.IsWhite(GRAY_3) && !sensor.IsWhite(GRAY_4)) //右侧越线
|
||||
{
|
||||
move.ForLeftward(speed_rate, LINE_FIX_SPEED_RATE);
|
||||
move.ForLeftward(speed_rate, CalcFixSpeedRate(sensor.GrayDeviationRate(GRAY_4)));
|
||||
}
|
||||
else if (sensor.IsWhite(GRAY_3) && sensor.IsWhite(GRAY_4)) //在白线上
|
||||
{
|
||||
@ -555,18 +656,18 @@ void LineForward(uint8_t end_position, float speed_rate)
|
||||
}
|
||||
else //均不符合，则低速后退，尝试回到白线上
|
||||
{
|
||||
move.Backward(LINE_FIND_SPEED_RATE);
|
||||
//move.Backward(LINE_FIND_SPEED_RATE);
|
||||
}
|
||||
|
||||
if (end_position == FRONT_END) //前端接触线离开函数
|
||||
{
|
||||
if (sensor.IsWhite(GRAY_1) && sensor.IsWhite(GRAY_2))
|
||||
break;
|
||||
if (sensor.IsWhite(GRAY_1) || sensor.IsWhite(GRAY_2))
|
||||
gray_match_time++;
|
||||
}
|
||||
else if (end_position == BACK_END) //后端接触线离开函数
|
||||
{
|
||||
if (sensor.IsWhite(GRAY_5) && sensor.IsWhite(GRAY_6))
|
||||
break;
|
||||
if (sensor.IsWhite(GRAY_5) || sensor.IsWhite(GRAY_6))
|
||||
gray_match_time++;
|
||||
}
|
||||
else if (end_position == CATCH_END) //到达抓取位置离开函数
|
||||
{
|
||||
@ -575,9 +676,13 @@ void LineForward(uint8_t end_position, float speed_rate)
|
||||
}
|
||||
else //到达释放位置离开函数
|
||||
{
|
||||
if (millis() - begin_time > RELEASE_MOVE_DELAY_TIME)
|
||||
if (millis() - begin_time > RELEASE_MOVE_FORWARD_DELAY_TIME)
|
||||
break;
|
||||
}
|
||||
|
||||
//对应前端接触线离开函数和后端接触线离开函数的情况
|
||||
if (gray_match_time == 2)
|
||||
break;
|
||||
}
|
||||
|
||||
#ifdef TAICHI_DEBUG
|
||||
@ -597,15 +702,18 @@ void LineBackward(uint8_t end_position, float speed_rate)
|
||||
Serial.println((int)end_position);
|
||||
#endif
|
||||
|
||||
//记录灰度传感器匹配次数
|
||||
uint8_t gray_match_time = 0;
|
||||
|
||||
while(1)
|
||||
{
|
||||
if (!sensor.IsWhite(GRAY_3) && sensor.IsWhite(GRAY_4)) //左侧越线
|
||||
{
|
||||
move.BackRightward(speed_rate, LINE_FIX_SPEED_RATE);
|
||||
move.BackRightward(speed_rate, CalcFixSpeedRate(sensor.GrayDeviationRate(GRAY_3)));
|
||||
}
|
||||
else if (sensor.IsWhite(GRAY_3) && !sensor.IsWhite(GRAY_4)) //右侧越线
|
||||
{
|
||||
move.BackLeftward(speed_rate, LINE_FIX_SPEED_RATE);
|
||||
move.BackLeftward(speed_rate, CalcFixSpeedRate(sensor.GrayDeviationRate(GRAY_4)));
|
||||
}
|
||||
else if (sensor.IsWhite(GRAY_3) && sensor.IsWhite(GRAY_4)) //在白线上
|
||||
{
|
||||
@ -613,19 +721,23 @@ void LineBackward(uint8_t end_position, float speed_rate)
|
||||
}
|
||||
else //均不符合，则低速前进，尝试回到白线上
|
||||
{
|
||||
move.Forward(LINE_FIND_SPEED_RATE);
|
||||
//move.Forward(LINE_FIND_SPEED_RATE);
|
||||
}
|
||||
|
||||
if (end_position == FRONT_END) //前端接触线离开函数
|
||||
{
|
||||
if (sensor.IsWhite(GRAY_1) && sensor.IsWhite(GRAY_2))
|
||||
break;
|
||||
if (sensor.IsWhite(GRAY_1) || sensor.IsWhite(GRAY_2))
|
||||
gray_match_time++;
|
||||
}
|
||||
else //后端接触线离开函数
|
||||
{
|
||||
if (sensor.IsWhite(GRAY_5) && sensor.IsWhite(GRAY_6))
|
||||
break;
|
||||
if (sensor.IsWhite(GRAY_5) || sensor.IsWhite(GRAY_6))
|
||||
gray_match_time++;
|
||||
}
|
||||
|
||||
//对应前端接触线离开函数和后端接触线离开函数的情况
|
||||
if (gray_match_time == 2)
|
||||
break;
|
||||
}
|
||||
|
||||
#ifdef TAICHI_DEBUG
|
||||
@ -638,15 +750,18 @@ void LineBackward(uint8_t end_position, float speed_rate)
|
||||
//直行或后退或转向，完成后离开函数但不停止。会自动跳过无需前往的释放点
|
||||
void TurnDirection(float speed_rate)
|
||||
{
|
||||
//若下下点为释放点，判断是否需要跳过
|
||||
if ((route[next_next_flag][TYPE] == RELEASE_POINT && (!is_claw_catch || is_carry)) || (route[next_next_flag][TYPE] == GETOUT_POINT && !is_carry))
|
||||
//若下下点为释放点或增益抓取点，判断是否需要跳过
|
||||
if ((route[next_next_flag][TYPE] == RELEASE_POINT && (!is_claw_catch || is_carry))
|
||||
|| (route[next_next_flag][TYPE] == GETOUT_POINT && !is_carry)
|
||||
|| (route[next_next_flag][TYPE] == GAIN_POINT && is_claw_catch)
|
||||
)
|
||||
{
|
||||
UpdateFlag(JUMP_DEAD_ROAD);
|
||||
|
||||
#ifdef TAICHI_DEBUG
|
||||
//调试输出直行或后退或转向状态
|
||||
Serial.println("#TAICHI: JUMP THE RELEASE/GETOUT POINT FOR NOTHING CARRIED");
|
||||
#endif
|
||||
Serial.println("#TAICHI: JUMP THE RELEASE/GETOUT/GAIN POINT FOR STATUS REASON");
|
||||
#endif
|
||||
}
|
||||
|
||||
uint8_t direction = CalcDirection();
|
||||
@ -670,10 +785,12 @@ void TurnDirection(float speed_rate)
|
||||
}
|
||||
else //继续转向
|
||||
{
|
||||
//等待小车旋转中心与十字中心重合
|
||||
if (direction == FORLEFTWARD || direction == FORRIGHTWARD)
|
||||
delay(BEFORE_FORTURN_DELAY);
|
||||
else delay(BEFORE_BACKTURN_DELAY);
|
||||
|
||||
//旋转
|
||||
move.MoveDirection(direction, speed_rate);
|
||||
|
||||
//等待一定时间后检测是否摆正
|
||||
@ -689,21 +806,31 @@ void TurnDirection(float speed_rate)
|
||||
|
||||
|
||||
//抓取环，并判定是否抓取成功
|
||||
bool CatchAndCheck(float speed)
|
||||
bool CatchAndCheck(uint8_t type, float speed)
|
||||
{
|
||||
//记录开始时间
|
||||
unsigned long begin_time = millis();
|
||||
|
||||
//抓取延时
|
||||
int catch_delay_time;
|
||||
|
||||
//抓取次数
|
||||
uint8_t catch_times = 0;
|
||||
|
||||
if (type == CATCH_TYPE_CATCH)
|
||||
catch_delay_time = CATCH_DELAY_TIME;
|
||||
else catch_delay_time = GAINCATCH_DELAY_TIME;
|
||||
|
||||
//执行抓取动作
|
||||
servo.Catch(speed);
|
||||
if (type == CATCH_TYPE_CATCH)
|
||||
servo.Catch(speed);
|
||||
else servo.GainCatch(speed);
|
||||
catch_times++;
|
||||
|
||||
//等待完成动作
|
||||
while (millis() - begin_time < CATCH_DELAY_TIME)
|
||||
while (millis() - begin_time < catch_delay_time)
|
||||
{
|
||||
#ifndef DISABLE_CLAW_CHECK
|
||||
if (sensor.IsPushed(BUTTON_1)) //开关 1 闭合，即爪子两端接触，说明抓取失败
|
||||
{
|
||||
#ifdef TAICHI_DEBUG
|
||||
@ -712,6 +839,9 @@ bool CatchAndCheck(float speed)
|
||||
Serial.print(" catch_times: "); Serial.println((int)catch_times);
|
||||
#endif
|
||||
|
||||
if (type == CATCH_TYPE_GAIN)
|
||||
delay(millis() - begin_time - catch_delay_time); //等待运行完成，防止卡住
|
||||
|
||||
//停止动作组运行
|
||||
servo.StopActionGroup();
|
||||
|
||||
@ -729,15 +859,27 @@ bool CatchAndCheck(float speed)
|
||||
begin_time = millis();
|
||||
|
||||
//执行抓取动作
|
||||
servo.Catch(speed);
|
||||
if (type == CATCH_TYPE_CATCH)
|
||||
servo.Catch(speed);
|
||||
else servo.GainCatch(speed);
|
||||
catch_times++;
|
||||
}
|
||||
#endif
|
||||
}
|
||||
|
||||
#ifndef DISABLE_CLAW_CHECK
|
||||
#ifdef TAICHI_DEBUG
|
||||
//调试输出成功信息
|
||||
Serial.println("#TAICHI: SUCCUESS CATCH!");
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#ifdef DISABLE_CLAW_CHECK
|
||||
#ifdef TAICHI_DEBUG
|
||||
//调试输出结束信息
|
||||
Serial.println("#TAICHI: CATCH WITHOUT CHECK!");
|
||||
#endif
|
||||
#endif
|
||||
|
||||
is_claw_catch = true;
|
||||
return true;
|
||||
@ -747,6 +889,16 @@ bool CatchAndCheck(float speed)
|
||||
//打开爪子，并判断爪子是否能正常工作
|
||||
bool OpenClawAndCheck(void)
|
||||
{
|
||||
#ifdef DISABLE_CLAW_CHECK
|
||||
#ifdef TAICHI_DEBUG
|
||||
//调试输出信息
|
||||
Serial.println("#TAICHI: DISABLE CLAW CHECK!");
|
||||
#endif
|
||||
|
||||
is_claw_ok = true;
|
||||
return true;
|
||||
#endif
|
||||
|
||||
//记录开始时间
|
||||
unsigned long begin_time = millis();
|
||||
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user